Being an avid softsphere player myself, and also now an assistant coach, I am constantly searching for skills and also drills to enhance both my team and my own performance for the game. When it comes down to it, fielding is a major element of the game, yet you cannot win a game without hitting and acquiring on base. Because my team this year is struggling with hitting particular pitches, I wanted to produce a softround tee we deserve to utilize at practice without having to take a lot of money out of tournament money.

For this task, I visited Menards for every one of the materials I needed. The Menards I saw (on 8fourth and Highmethod 2 in Lincoln, NE) had every one of the components essential situated in the Pipes and also PVC Pipe area. I would assume a lot of of the stores would certainly be set up the same means and also that is wright here you will be finding most of these materials! The only components I did not find in this location of the save were the Wood Screws, found in the Nail and Screw Department, and also the Furniture Leg Tips, as this item was situated in the Home Department which was best beside the Nail and Screw Department, and the Spray Paint which is located in the Repaint Department. The employees there were extremely beneficial through directing me to the best places and also finding the best size parts I essential to complete the softround tee. So if you’re having actually trouble, just ask! In full I invested about $29 compared to going to Scheel’s and also buying a $99 SKLZ Weighted Pro-Level Tee.

You are watching: How to make a batting tee for softball


*

For this project you are going to need the following materials:

· 4 Wood Screws - $.82 (I currently had actually a couple of additional timber screws laying around)

· 1 Discharge Hose, also recognized as Washing Hose at Menards, 7/8” ID x 1 ¼” OD 2’ in size - $3.89

· Plylumber (I saw the scrap area and also found a couple of pieces that operated nicely, you deserve to buy larger pieces and also reduced them dvery own which is what I did) approximately 11” x 11” (I provided the size of a piece of paper to measure) - $2.89

· 1 Galvanized Iron Floor Flange 1 ¼” - $5.59

· 1 PVC Pipe Fitting, you’ll want to find the Schedule 40 Male Threaded Adapter 1 ¼” – $5.45

· 1 PVC Pipe, aacquire look for Schedule 40, 1 ¼” diameter (This came through the just choice of 4’ in size so you will certainly need to cut it dvery own, mine was reduced to 2’) - $ 3.99

· 1 fill of Shepherd Rubber Furniture Leg Tips 1 ½” (These came in a pack of 4, I discovered that they were not easily accessible at Menards and also gained a 1 1/8” in place which simply cause minor adjustments to the tee) - $2.59

· Spray Repaint (optional, I offered two colors) - $4.99 (total)

· Sand also Paper (Optional, I had actually my very own, I used 220 Grit) – $2.17

· Weights (Optional cost will certainly differ relying on brand and also size of the weight)

You will likewise need the complying with tools:

· Saw (I had actually a table observed that I was able to usage otherwise a hand also saw will execute just as good)

· Screwdriver or Power Drill (I offered the power drill as a result of exactly how thick the wood was that I supplied yet either one will work)

· Utility Knife

· Vice (Optional yet would certainly very indicate if functioning alone)


Take your plylumber and meacertain it to your liking, I provided a rough estimate of what a home plate would certainly be and also cut the lumber to 11” x 11”. If you do not have actually a measuring tape near you, you deserve to usage a item of paper to measure it by making use of the size of the paper which is 11”, this is what I did.


*

On the plywood facility the Galvanized Iron Floor Flange. Once you have focused the floor flange you will must grab your screwdriver or power drill and also your 4 timber screws. There will certainly be 4 circular cut outs on the floor flange, this will be where your screws will be placed to organize the flange in place. (Make certain that the screws are not as well narrowhead, this will certainly cause the flange to relocate out of area, the screw head should be bigger than the opening to the circular cut outs. Also be certain that the screws will not poke via the bottom of the hardwood, this could possibly reason injury once picking up the tee and will also cause it to be unwell balanced.) Carefully screw or drill the screws into place. After you have actually screwed the floor flange right into location try to relocate it roughly, if it does not budge you can continue to step 3, if it moves you will desire to either tighten the screws even more or try a bigger head screw.


*

Next off you will certainly require your Schedule 40 Male Threaded Adapter PVC Pipe Fitting. The Galvanized Iron Floor Flange will have actually thanalysis on the inside of the big middle opening. You will certainly must take the threaded side of the PVC Pipe Fitting and also screw that into the Galvanized Iron Floor Flange. You will certainly want to screw down the PVC Pipe Fitting as tight as you have the right to acquire it.

On my tee the PVC Pipe Fitting did not go all the way down, as long as you have the Fitting touching the top of the plytimber you are okay!


*

Be extremely careful and safe via this action I would additionally imply having one more perchild with you for this step! For this step you will need your table or hand also witnessed. I would certainly advise making use of protective eye wear and also gloves for this step. Take your PVC Pipe and meacertain the pipe to be about 2’. Again, I did not have a tape meacertain handy so I offered paper to meacertain, I took 2 pieces size wise and also supplied the width of my middle and tip finger to estimate around 2’. Mark off wbelow you are going to be cutting the piece at. (I had added help through this as my friend was the one who owned the table saw and I felt more comfortable via her mirroring me and helping me operate the machine as she had all the correct safety and security tools.) If you are doing this action alone you will certainly desire to have actually a vice to hold dvery own the PVC Pipe as the Pipe will roll approximately once you are sawing it. Due to the fact that I had an additional perchild via me when doing this action I had the ability to organize the PVC pipe in place while my frifinish cut the pipe at our mark. If making use of a table saw be mindful of the plastic pposts that will certainly fly off when cutting, they can be hot, be certain to wear protective eye wear and gloves!


Be extremely careful via this step! For this action I had to improvise. They didn’t have actually the correct sizing of Furniture Leg Tips (1 ½”) so I obtained 1 1/8” reasoning it would stretch enough to fit. I was wrong yet there is a means to make it work-related that is simply as efficient as the various other sizing would certainly have actually been! You’re going to be trying to find a snug friction fit through the 1 ¼” Discharge/Washer Hose. I measured approximately the hose and used that as a recommendation as soon as I was cutting. Here are the measures for either measurement:

A. 1 ½” Furniture Leg Tips – Tbelow will certainly be a side that is already reduced open up and a side that is cshed (the component that would certainly touch the floor if it was on furniture), this is the side you will be cutting out. If you have a power drill handy a 1 1/8” Forstner little will come in handy and also will certainly be a safer choice. If you have actually the drill and little simply drill the closed side out so you can see out of each finish. If you carry out not have the drill and also little bit you will certainly need to use a energy knife to reduced the closed finish. This will take a lot of time as the rubber is incredibly thick. After you have actually cut the rubber out you will certainly should stretch it out for a couple of minutes as you will be extending the already opened end over the PVC pipe. It will certainly not want to initially fit but via sufficient stretching and forcing it will! After you acquire component of it on you can put the leg guideline on the floor and push the staying piping in. Insert the other end of the PVC pipe into the Male Threaded Adapter (the base of the tee).

B. 1 1/8” Furniture Leg Tips – For this step you will certainly need a energy knife in addition to the Furniture Leg Tip. Keep in mind you must have actually 4 of them so it’s okay to make a few mistakes. For this path I measured 1 finger width from the open finished guideline and marked that spot. Use the energy knife to reduced alengthy that mark to make a ring out of the Furniture Leg Tip. Take your time and also be careful as the rubber likes to move around when you are cutting it! After you finish cutting the guideline you deserve to insert the PVC Pipe right into the Male Threaded Adapter (the base of the tee). Place the ring you reduced out on the height of the PVC Pipe (the side that is not on the base of the tee).


This step will certainly be the same for either strategy offered above. Take the Discharge/Washer Hose and insert it into the Furniture Leg Tip/PVC Pipe (this is the stem of the base). This will certainly be a tight fit but it is going to keep the hose in location so it does not slide dvery own right into the PVC pipe when you are trying to hit. This part of the tee will be adjusecure so you deserve to raise or reduced the position of the sphere relying on where you would certainly like to exercise your hitting. (If you chose to perform the 1 1/8” Furniture Leg Tip, the just difference will certainly be that if you want to raise the hose you will have to host the ring you cut out in place, other than that it will certainly slide conveniently when trying to reduced the tee.)


*

If you would choose to, you can usage sand paper to sfrequently the sides of the plytimber, I would recommend this action if you are going to be transferring the tee often to prevent splinters. I provided 220-Grit sand also paper and also by hand sanded dvery own the sides of the plywood to make a smooth finish.

Another action you can carry out is spray paint your tee to include in extra flare or make it even more personal. I determined to spray paint my tee the colors of my softsphere team (babsence and also purple) to collection the tee acomponent from everyone else’s. When spray painting be sure to follow the directions on the fill of the have the right to. I would certainly recommfinish taking apart the specific pieces you desire to spray paint, paint them, permitting the appropriate drying time, and then reassembling the tee after they have actually entirely dried. For me the drying time was approximately 20 minutes however I let it dry overnight just to be safe!

Finally, you deserve to likewise include weights to the base of the tee to aid the balance and also sturdiness of the tee. The weights will certainly help the tee remain up right as soon as the bat hits both the round and tee, or if you plan on utilizing the tee throughout a windy day. I would certainly recommfinish the weights to civilization who setup on using this tee who are slap hitters, power hitters, or younger kids. Depfinishing on the hitter, their weight, height, and style of hitting, I would certainly use everywhere between 5-20 pounds.

See more: I Like School School I Like School South Park, Littered With A Litter


Even in the case that this homemade one doesn’t make it through as long I’m sure I can discover various materials that would certainly broaden the life expectancy and I’m already planning on creating brand-new tee, a dual tee, to emphasis on hitting inside and also external pitches or level swinging, together with making a couple of alterations to the materials I provided in this job to make the tee a tiny even more sturdy.